No products available yet
Stay tuned! More products will be shown here as they are added.
Stay tuned! More products will be shown here as they are added.
U-Ring | Profile | Material | Hardness | Bars | Temperature | Speed |
Piston / Rod | PU / TPU | 92 / 93 SH A | ≤350 | -20 to +100 ºC | ≤0,50 m/s | |
Piston / Rod | NBR | 90 SH A | ≤400 | -30 to +105 ºC | ≤0,50 m/s |
Symmetrical U-rings are very versatile as they can be used on both the piston and the rod. For hydraulic applications, PU or TPU are the standard materials while pneumatic applications will use NBR. Whether the application is single-acting or double-acting, this model offers high sealing efficiency as well as excellent resistance to abrasion, wear and friction. JIOrings offers a range of almost 2,000 standard sizes.
Construction machinery, fork-lift trucks , injection moulding machines, agricultural machinery, loading platforms and standard cylinders.
NBR90 | |||
MEDIA | Mineral oils (DIN 51524) | HFA & HFB | HFC |
TEMPERATURE | -30° C to +105 °C | +5 °C to +60 °C | -30 °C to +60 °C |
PRESSURE | ≤150 Bar | ≤150 Bar | ≤150 Bar |
SPEED | ≤0,5 m/sn | ≤0,5 m/sn | ≤0,5 m/sn |
PU92 / TPU92 / TPU93 | |||
MEDIA | Mineral oils (DIN 51524) | HFA & HFB | HFC |
TEMPERATURE | -30°C to +100°C | +5 °C to +50 °C | -30 °C to +40 °C |
PRESSURE | ≤400 Bar | ≤400 Bar | ≤400 Bar |
SPEED | ≤0,5 m/sn | ≤0,5 m/sn | ≤0,5 m/sn |
TPU95 High performance | |||
MEDIA | Mineral oils (DIN 51524) | HFA & HFB | HFC |
TEMPERATURE | -35 °C to +110 °C | +10 °C to +50 °C | -35 °C to +50 °C |
PRESSURE | ≤400 Bar | ≤400 Bar | ≤400 Bar |
SPEED | ≤0,5 m/sn | ≤0,5 m/sn | ≤0,5 m/sn |
Ra | Rmax | |
Dynamic surface | ≤0,3 μm | ≤3,0 μm |
Groove base | ≤1,8 μm | ≤10,0 μm |
Groove flanks | ≤3,2 μm | ≤16,0 μm |
Easily assembled into closed grooves according to the minimum diameter values that are given in the below table. Open grooves or special assembly tools should be used for the values that are outside this table. It is very important that the assembly tools must be of soft material and have no sharp edges. Before installation the wiper must be oiled with system oil.
Minimum diametre values for closed type of grooves | |||||||
(D-d)/2 (mm) | 4 | 5 | 6 | 7,7 | 10 | 12,5 | 15 |
dmin (mm) | 25 | 30 | 40 | 50 | 80 | 100 | 105 |
Maximum permissible gap NBR | |||
C/S | Pressure (Bar) | ||
50 | 100 | 160 | |
≤5 | 0.40 | 0.20 | 0.10 |
>5 | 0.45 | 0.25 | 0.15 |
Maximum permissible gap PU/TPU | |||
C/S | Pressure (Bar) | ||
150 | 250 | 400 | |
≤5 | 0,30 | 0,20 | 0,15 |
>5 | 0,35 | 0,25 | 0,20 |